When your indoor plumbing isn’t functioning properly it can be a real pain in the rear end. You could pick up the phone and call a reputable plumber nearby who can come to the rescue, but, depending on the situation you could also take control of the situation on your own. Consider these tips for common toilet repair and, with any luck, your problems might be solved with a little bit of elbow grease and common household tools.
Phantom flushes are a sign that something is not quite right deep inside your toilet bowl. This problem is usually caused by a slow leak into the toilet bowl from the tank and is a toilet repair that you can handle with minimal plumbing experience. Usually, the flapper is the culprit which has a tendency to go bad after many years of service. The fix is fairly simple and requires draining the toilet completely, inspecting the flapper and flapper seat, then heading to your nearest home improvement store for a replacement if it appears worn or broken.
A clogged toilet is one of the most common plumbing problems in a house and not necessarily one that needs professional attention. At least, not before you try freeing the clog yourself. Use a force-cup plunger to clear the clog by affixing it over the drain hole and forcing water deep into the toilet. This forceful motion is usually enough to move the clog from where it’s trapped and allow the water in the toilet bowl to drain.
If you hear a faint but constant trickle of water emanating from your toilet, that signals another problem that you might be able to tackle on your own. You’ll need to drain the toilet like you read about for addressing phantom flushes, and then carefully inspect a few parts inside the tank, namely: the refill tube, the float, and the inlet valve assembly. Check for any damage to any of the parts. The fix might be as simple as replacing anything that appears worn over time.
Over time and use, the hinges that attach the lid to the toilet can begin to fail. Luckily, your toilet seat cover is pretty easy to replace. Remove the old one from the toilet and measure it carefully. Take those measurements to a home improvement store near you and find a suitable replacement. Affix the new lid and, in no time flat, your previously broken toilet will be good as new.
For some homeowners, indoor plumbing can be an intimidating mystery that they’d rather leave up to the pros to handle. And plumbers in your area are just fine with that. There are some things that a homeowner can do, however, to help support the proper function and longevity of their plumbing system. Consider these plumbing solutions brought to you by your trusted neighborhood plumbing service.
Even if you don’t know how to handle any other plumbing issue, the key plumbing solution that you should know is where your water main is. In the event of an emergency that sees water pouring into your home from broken pipes, shutting off the main is key for minimizing the damage that that situation might cause. The main to your home is typically located somewhere near your hot water heater and will feature and easy to maneuver shut off valve that should stop water from being serviced inside your home.
Sure you could call your friendly, neighborhood plumber every time you have a clogged drain. They’d be happy to help you out any way they can. But this is a household situation where you can learn to handle yourself with the right tools. It’s smart to have a plunger and maybe even a snake tool on hand so that you can remove or push through any clogs in the system.
You might think that both your toilets and your garbage disposal can handle anything you throw it’s way. That’s not necessarily true. It doesn’t take much to clog a toilet and a disposal, so it’s wise to treat both with care. Both appliances have big, important jobs to do. It’s important to treat them tenderly and to keep a plunger on hand in the event of any clogs that you can handle on your own.
Frozen pipes can be a homeowner’s nightmare. So anytime the weatherman on TV predicts a chilling cold snap headed your way, do what you can to protect your pipes. Add cold weather protection to any exposed pipes, and if your home is lifted on piers, consider having a plumber come out to ensure the plumbing is winterized.
Everyone knows who to call for burst pipes or a damaging water leak. But did you know that plumbers actually provide a host of other services? If you’re a homeowner, you should consider these four plumbing services that you probably didn’t know you needed and that a plumber can provide until now.
Your friendly neighborhood plumber isn’t just an expert when it comes to water, but they’re also a pro when it comes to dealing with gas. If you have natural gas as a fuel source in your home, the line was probably put there by a licensed plumber. If you need that line extended, or even a brand new line run to a different area on your property, a plumber is the one to call for this unexpected plumbing service.
If you’re eyeing a bathroom remodel in the near future, you’ll definitely need a skilled and knowledgeable plumber. These professionals can help move important features of the bathroom—like your toilet or shower—to different locations in the room. They can also run new pipes if necessary, and offer more guidance on the best practices for the remodeling project.
Many homeowners take the safety of their indoor plumbing to a whole new level by installing a whole-house water purifier. These appliances guarantee that your family is drinking and using the safest water possible. The professional that can help with the safe and timely installation of a water purifier is your friendly, neighborhood plumber.
If you start noticing damp spots on your floor, you might just have a slab leak on your hands. This means that a pipe contained within the slab is leaking and requires immediate attention. An experienced plumber is the best person for this job which will require accessing the pipe for rerouting or repair.
Indoor plumbing took a long time to become part of almost every American household. In fact, even in 1940 only half of them had any type of indoor plumbing. Thankfully, those days are behind us and indoor plumbing is the norm. When plumbing problems creep in like leaks, it can quickly feel like the years before 1940 again. It’s smart to call in help quickly and here’s what you can expect from leak repair.
The first critical step in leak repair is to shut off the water. Water can do tremendous damage to a structure and shutting off anything actively running is key. If the water leak is between the service line and the home’s pies, you can turn the water off at the main. If it’s in the service line, you’ll need to turn the water off at the meter.
When you have a major water leak, it can present an extremely dangerous situation if it mixes with electricity. It’s smart if you have water in your home to also turn the electricity off at the breaker until the situation improves. If the leak is relatively small, it may just require unplugging any appliances in the immediate vicinity of the area.
An emergency plumber is the perfect professional to provide leak repair. Making sure they’re licensed and insured means that you’ll get high quality work and benefit from the experience of a seasoned pro. The plumber will find the leak and isolate it so that a fix can be applied and your water restored.
Depending on the size of the leak, the hole could be fixed quickly or might take a little bit of time. It might require a new pipe, or it might be able to be salvaged with just a patch. A knowledgeable plumber will know and get the water flowing back into your home in no time flat.
What’s not to love about an old house? Imagine the stories it would have if walls could talk. Perhaps the only thing that’s hard to love about an old house is the to-do list that will probably never go away when you own it. One thing that might land on that list depending on the age of the structure is a whole house repiping, and here’s what you can expect if that’s in your future.
There are few solid reasons that it’s time for whole house repiping. If your home is very old and has lead pipes, it’s wise to consider the job for the health of your family. This type of pipe usually exists in homes built well before 1920. The same goes for galvanized steel. It was a popular construction material in the U.S. but the material corrodes over time and must be replaced. If you find yourself calling the plumber often, that’s another sign that your house might be ripe for a repiping.
If you already have a plumber for the job, you can skip to the next item. If you don’t, you’ll have to go through the process of getting estimates for the job. The golden rule is to get three to be sure you’re getting a fair price for the work. Having a professional look at the situation also informs if you need to repipe the whole house at once, or if you can go section by section over time.
The first thing that your plumber will do is shut off the water to the house. It will remain that way for the entire job, so if you have some place comfortable to wait out the project, it’s a good option. Specialized tools will be used to identify the exact location of the pipes to minimize the damage to the drywall. Replacement pipes are installed through holes in the drywall which are patched and repaired once the new piping is in place.
The answer to this question depends entirely on the size of your home. A large home could take a week or more to repipe. A small home might be done in a day or two. The estimated time for completion will be included in your estimate and it’s wise to check in with the plumber each day during the job for a progress update.
We rely on the predictability of faucets more than we realize. And modern humans are pretty spoiled by them. Long gone are the days of hauling water to the house from a nearby well. And that gratitude isn’t often fully appreciated until the convenience is gone. If you’re dealing with a malfunctioning faucet on your end, consider these steps for leaky faucet repair in Port St. Lucie. You can try fixing it yourself, or call in the experts for a professional job.
The first step in fixing your leaky faucet is to know what kind of faucet you have. Common household faucets usually fall in one four categories: ball type, cartridge, ceramic disk, or compression. The guilty culprit for a leaky faucet tends to involve valves, washers, seals or O-rings. Once you figure out the type of faucet you’re dealing with, and the culprit causing the problem, you’ll be one step closer to leaky faucet repair.
The very first thing you’ll need to do to successfully fix your leaky faucet is to shut off the water supply to the faucet which is probably under the sink. It’s smart to lay a rag over the drain hole so that no little pieces inadvertently fall where you don’t want them to. With a wrench, you’ll gently remove the decorative cap if there is one, and quickly get into the cuts of the faucet. Have a mild solution of white vinegar nearby and a course scrubbing pad that you can use to remove any mineral deposits that might have collected on the faucet parts.
If you have a compression faucet, you’re probably looking for a malfunctioning O-ring that needs to be replaced. If you have a ceramic faucet, you’ll probably need to replace the seals to stop the leak. If you have a ball-type faucet, there’s a good chance you’ll be replacing the spring and seat. Replacement kits for these sink types are sold at most home improvement stores.
Fixing a leaky faucet isn’t the most difficult project in the world. But some people would rather not be bothered with understanding the inner workings of their bathroom or kitchen faucets. If that sounds more like you, pick up the phone and call an expert in to get the job done fast. You’ll be back to the modern conveniences of running water, on demand, in no time.
Aside from your kitchen and laundry room, your bathrooms are the workhorses of your home. They take a beating and can start to show their age when the rest of your home continues to look impeccable. If you’re looking for options for bathroom remodels including bathtub replacement, here are a few things to consider.
If your bathroom space really just needs a bathtub replacement, there are many options on the market. A standard tub is the everyday variety that gets the job done just fine. Of course, there are also jetted tubs and soaking tubs that provide a bit more in terms of relaxation and rejuvenation. Walk-in tubs are a great idea for older folks, and freestanding tubs are a current trend in bathroom design that doesn’t look like it’s going anywhere anytime soon.
Your bathtub replacement can be as simple or as extravagant as you want it to be. The more extravagant, the more it’s likely to cost you too. The cost for a replacement tub can range from $300 on the low end, to $5,000 or more on the high end. That doesn’t even include the cost of installation.
One of the most important chores to complete before you start shopping for a bathtub replacement is to measure the tub currently in place. Traditional measurements for bathtubs include the length, width, and depth of the entire tub. You’ll also want to measure the basin length, width, and depth too.
Installing your bathtub replacement should be a fairly easy job provided you hire an experienced plumber who knows what they’re doing. They will begin by shutting the water off to your home and dismantling the connections to the old tub. The old tub will then be removed to make way for the new one. The plumber will take care of connecting it to your plumbing system and you’ll be soaking in a brand new tub in no time at all.
What would life be like without your home’s hot water heater? Miserable, most likely—cold showers, clothes washing limitations, stuck on food in the sink requiring tons of scrubbing. Of course, those are all first world problems and we should all be really grateful that they’re the biggest things we need to worry about. But when your hot water heater goes out, and water heater repair is the order for the day, it probably won’t be fun and here’s what you’ll need to know about the process.
When it’s clear your water heater is no longer functioning as it should, it’s time to call the pros. You’ll need a knowledgeable plumber to come in inspect the malfunctioning water heater to determine the source of the problem and whether it can be repaired or must be replaced. If repair is the course, you can expect these steps for water heater repair.
One of the first steps that your plumber will make is to test the electrical components of the water heater to find out if they are to blame for the breakdown. Heating elements are a common problem maker and if that’s the root cause of your hot water heater woes, you’ll be back up and running in now time. In fact, considering all hot water heater problems, replacing the heating elements solves the issue in about 90 percent of all cases.
If you find that your water heater is leaking and that water is puddling in the vicinity of the appliance, waste no time and call your trusted water heater repair professional. The sooner you act the less water damage you’ll have to contend with once the repair is made. The problem might simply be the drain valve, temperature pressure relief valve, or element gasket. A seasoned pro will have you back up and running in no time.
It’s common for water heaters to bubble gurgle as they process and heat water for use throughout your home. If you begin to hear a knocking sound, it might mean that sediments from the water supply have built up in the bottom of the tank and need to be addressed. Humming might point to a faulty heating element and popping might signal an issue with the water supply.
Great plumbers are a great asset for homeowners. Plumbing problems really have no sense of time and have a tendency to happen when you least expect them and at inconvenient times. If you don’t already have a great plumber in Port St. Lucie on speed dial, here’s how to find one that will be responsive when you need them, knowledgeable, and with the experience it takes to get the job done right.
Port St. Lucie has plenty of plumbers listed in the yellow pages, but how do you find the best ones? There are a couple of different ways that you can go about this but rest assured, when it’s said and done, you’ll likely have one of the very best in town ready to assist when you need them. A little bit of leg work now when you don’t necessarily need the best plumber in Port St. Lucie will save you time, money, and anxiety when the occasion arises that you do.
One of the easiest ways to find a great plumber is to head to the same place they go. There are shops all over that specialize in plumbing supplies and other home hardware. It’s likely that the owners of this shop, and the employees that work there, have a pretty good sense of the plumbers working in your community. March right up to the register, or ask for a store manager, and then inquire if they keep a list of talented and experienced plumbers on hand for homeowners in need just like you.
Here’s a secret, if you search the internet for the best plumber in Port St. Lucie, you might not necessarily find the best. Ensuring you find the best takes a little more work beyond the search. Once you have a list of candidates, spend some time looking at their websites and social media pages to determine if the best label should apply. Customer reviews left on search engines and social media pages also go a long way in advising if you’re really found one of the best.
Another solid way to find great plumbers in your area is to ask around. You probably have family and friends who have homes of their own and have, most likely, needed a plumber at some point in time. Their experiences could save you some time and money. As your friends, family, and acquaintances for their recommendations and you might be well on your way to peace of mind.
The bathrooms in your home are a great place to spend money. Any improvements that you make to these spaces will impress buyers in the future in the event you decide to list your home. Industry experts agree that bathrooms, and bathtub replacement, are two home improvement projects that deliver the most bang for your buck. So, what are your options?
If the bathroom is ok but the bathtub really needs to go, or has seen better days, replacing it in the same footprint is a relatively easy job. The first step would be to find a dependable plumber that can help you through the bathtub replacement process. He or she can tell you exactly what you need to make the job as easy as possible and direct you to the exact dimensions for your shopping trip to pick out a new tub.
A knowledgeable plumber will definitely be involved if you plan to replace your bathtub but place the new tub in a different place. They might need to move the pippin necessary to deliver water to and drain the tub. It’s possible to rearrange your bathroom and it might make a lot of sense in the space. Just be sure you have an experienced plumber advising you along the way.
If your bathroom has a shower but no tub, there might be a good reason to add one like small kids in the home, or even pets that need regular bathing. Discuss the space with a plumber to know if there is enough room to add the tub. There are all sizes of tubs on the market, so even if the room is tight, you might still be able to incorporate a new bathtub.
Real estate experts estimate that homeowners get a 70 percent return on any investments they make in renovating the bathrooms of their home. If you have the budget, and really dislike the space as it exists currently, it might make sense to discuss a full-scale renovation. Find a plumber that you can trust with a solid reputation in the community and plenty of experience to guide you on your renovation journey.